Indexable milling Recommended cutting data Recommended feed rate Indexable milling – group 2 (FMA01/02/03/04, FME02/03/17, FMP01/02, EMP01/02/03/04/05/14) Material group FMA01 | FMA02 SEET12 FMA03 SEKN12 FMA03 SEKN15 FMA04 OFKT05 FMA04 OFKR07 FMA04 ODHT06 Feed rate per cutting edge [mm] Unalloyed steel Low-alloyed steel F F 0,15 0,14 M 0,20 0,19 R 0,25 0,23 High-alloyed steel and high-alloyed tool steel 0,13 0,18 0,22 Stainless steel Grey cast iron Cast iron with spheroidal graphite Malleable cast iron Aluminium wrought alloys Aluminum cast alloys Copper and copper alloys (bronze/brass) Heat-resistant alloys Titanium alloys Hardened steel Hard cast iron Hardened cast iron 0,11 0,14 0,18 0,17 0,15 0,15 0,13 0,13 0,11 0,11 0,11 0,22 0,20 0,20 0,17 0,17 0,15 0,14 0,14 0,28 0,25 0,25 0,21 0,21 0,19 0,18 0,18 P M K N S H R F M 0,18 0,17 0,16 0,13 0,20 0,18 0,18 M 0,20 0,19 0,18 0,14 0,22 0,20 0,20 Application R F 0,20 0,19 M 0,25 0,23 R F 0,20 0,19 M 0,25 0,23 R F 0,20 0,19 R M 0,25 0,23 0,18 0,22 0,18 0,22 0,18 0,22 0,14 0,18 0,14 0,18 0,14 0,18 0,22 0,20 0,20 0,17 0,17 0,15 0,14 0,14 0,28 0,25 0,25 0,21 0,21 0,19 0,18 0,18 0,22 0,20 0,20 0,17 0,17 0,15 0,14 0,14 0,28 0,25 0,25 0,21 0,21 0,19 0,18 0,18 0,22 0,20 0,20 0,17 0,17 0,15 0,14 0,14 0,28 0,25 0,25 0,21 0,21 0,19 0,18 0,18 Non-metallic materials X Note: The given cutting values are guide values, which were determined under ideal conditions. The values have to be adapted in individual cases. Indexable milling – group 2 (FMA01/02/03/04, FME02/03/17, FMP01/02, EMP01/02/03/04/05/14) Material group EMP03 | EMP04 APKT11 EMP05 ADKT** EMP14 VPGT22 Feed rate per cutting edge [mm] Unalloyed steel Low-alloyed steel F 0,12 0,11 M 0,17 0,16 R 0,23 0,21 F 0,10 0,09 M 0,15 0,14 R 0,20 0,19 High-alloyed steel and high-alloyed tool steel 0,10 0,15 0,20 0,09 0,13 0,18 Stainless steel Grey cast iron Cast iron with spheroidal graphite Malleable cast iron Aluminium wrought alloys Aluminum cast alloys Copper and copper alloys (bronze/brass) 0,08 0,12 0,16 0,07 0,11 0,14 0,13 0,12 0,12 0,10 0,10 0,09 0,19 0,17 0,17 0,15 0,15 0,13 0,25 0,23 0,23 0,20 0,20 0,18 0,11 0,10 0,10 0,09 0,09 0,08 0,17 0,15 0,15 0,13 0,13 0,11 0,22 0,20 0,20 0,17 0,17 0,15 Application F M R 0,05 0,05 0,05 0,2 0,2 0,2 0,3 0,3 0,3 Heat-resistant alloys Titanium alloys Hardened steel Hard cast iron Hardened cast iron P M K N S H Non-metallic materials X Note: The given cutting values are guide values, which were determined under ideal conditions. The values have to be adapted in individual cases. A i g n n r u T B g n i l l i M C g n i l l i r D D l a c i n h c e T n o i t a m r o f n I E x e d n I B 50